EN1A Steel Round Bar, EN1A Steel Round Bar Manufacturers, EN1A Steel Suppliers, EN1A Stockist, EN1A Steel Dealers, EN1A Steel Distributors, EN1A Wholesalers, EN1A Steel Traders, EN1A Steel Square Distributors, EN1A Steel Flat Bar, EN1A Steel Companies Near me.
 
Grade Introduction:
EN1A is a very popular grade of low carbon-manganese free cutting steel, which is most suitable for the manufacture of repetition turned components, such as nuts, bolts, hydraulic fittings, and studs, particularly where intricate drilling and machining operations are involved. 
 
It can be case-hardened, producing components with enhanced wear resistance. En1a is also available as En1a leaded (En1aPb) for greater machinability. Swarf will form in small chips to prevent machine blockage.
 
EN1a Non-Leaded steel is a Re-Sulphurised Free-Machining Steel. This is a premium grade of free-cutting steel. It has excellent machinability. It is suitable for case hardening and electroplating. We can provide you with free cutting steel both in the black and bright cold drawn bar form.
 
Grade Application:
En1a steels are suitable for applications where good machinability is the prime consideration. Because of this, they are used for the rapid production on single or multiple spindle automatic lathes and capstan lathes of finely finished components that will not be subjected to high stresses in service, e.g. light duty studs, cycle components, and many intricate parts for textile and printing machinery. This type of steel cannot be relied upon to possess good transverse properties and should not be used for hollow parts which might be subjected to an internal pressure that would set up wall stresses dangerously near to the transverse yield stress. Case hardening can be carried out but this steel Is not recommended for general case hardening work and it is not intended for use where the hardened case is subject to severe impact in service.
 
Typical applications are:
  • Brake hose end,
  • Hydraulic parts,
  • Pulleys,
  • Disc brake pistons,
  • Wheel nuts and inserts,
  • Control linkages,
  • Hear box components (case hardened),
  • Domestic garbage bin axles,
  • Concrete anchors,
  • Padlock shackles,
  • Hydraulic fittings,
  • Vice jaws. 
En1a steel bars are used mostly in bright form.
 
Equivalent grades:
BS970: 1955 EN1A, BS970/PD970: 1970 onwards 230M07. 
Related European grades: 9SMn28, BS En 11SMn30
Werkstoff no. 1.0715
US Grades SAE (AISI) 1213, 1215.
 
Addition to other grades:
MS, EN3B, EN8, EN8D, EN9, EN19, EN24, EN31, EN32B, EN36C, EN41B, EN43B, EN47, EN353, IS2062, 42Crmo4, HCHCR, OHNS, D2, D3, H-11, H-13, CW-1, M2, M35, M42, 2714, SKD-11, P20, P20+S, P20+Ni, SCM 420, ASTM SA-36, ASTM SA-105, SAE 1018, SAE 1020, SAE 4140, SAE 8620, 16MNCR5, 20MNCR5, C20, C35, C40, C45, C50, C60, CK45, 20C8, 40C8, 45C8, 55C8, C55MN75, SAE 52100, S40C, S355J2G3.
 
Our Supply Range:
 
Price List:

 
People also search as:
EN1A, EN1A Steel, EN1A Chemical composition, EN1A Mechanical properties, EN1A Equivalent Grades, EN1A Steel plate, EN1A Steel sheet, EN1A Manufacturers, EN1A Suppliers, EN1A Dealers, EN1A Stockist, EN1A Distributors, EN1A Wholesalers, EN1A Traders.
 
Chemical composition:
The following table shows the chemical composition of EN1A steel:
Element
C
Si
Mn
P
S
Content(%)
0.07-0.15
0.10 Max
0.80-1.20
0.07 Max
0.2-0.3
 
Mechanical Properties:
PROPERTIES
METRIC
IMPERIAL
Hardness, Brinell (typical)
300
33
Hardness, Rockwell C (typical)
30
30
Tensile strength, ultimate
965-1030 MPa
140000-150000 psi
Tensile strength, yield
827-862 MPa
120000-125000 psi
Elongation at break (in 50 mm (2″))
20.0%
20.0%
Compressive strength
862 MPa
125000 psi
Charpy impact (V-Notch)
27.1-33.9 J
20.0-25.0 ft-lb
Poisson’s ratio
0.27-0.30
0.27-0.30
Elastic modulus
190-210 GPa
27557-30457 ksi

 

FINISH
YIELD N/MM2
TENSILE N/MM2
ELONGATION MIN
HARDNESS HB
Turned
230/310
370/500
17
100/150
Drawn
290/550
400/650
7
115/200
 
Hardness:
300

 

Heat treatment: 
  • Carbonization of EN1A bright mild steel takes place at 900-950 o C then it is a furnace or air-cooled. 
  • En1A can be tempered at 180-210  o C then should be left to cool in the air.
  • The mild steel can be hardened at 780-800 o C then quenched in oil or water. However, this is difficult to do with EN1A and is not recommended.
 
Hardening:

 
Tempering:
En1A can be tempered at 180-210 oC then should be left to cool in the air. 

 

Physical Properties:
 
Thermal Properties:
 
Forging Properties:
 
Stress Relieving:
 
Normalizing:
 
Annealing:
 
Density:
 
Machinability:
 
Welding:
Welding is not recommended due to high sulfur and lead content.

 

Supply Cities:
Ahmedabad, Amaravathi, Ambattur, Bangalore, Belgaum, Chennai, Chittoor, Coimbatore, Dindigul, Mysore, Nellore, Hyderabad, Kochi, Mangalore, Tirupur, Tuticorin, Madurai, Andhra Pradesh, Karnataka, Puducherry, Kerala, Tamil Nadu, Telangana, Salem, Thanjavur, Trichy, Erode, Vellore, Ranipet, Sivakasi, Karur, Hosur, Nagercoil, Kanchipuram, Karaikudi, Neyveli, Cuddalore, Kumbakonam, Thiruvannamalai, Pollachi, Rajapalayam, Gudiyatham, Pudukottai, Vaniyambadi, Ambur, Nagapattinam, Trivandrum, Vijayawada, Guntur, Thirupathi, Nazarathpet, Kakinada, Kurnool, Kadapa, Nizamabad, Mahabubnagar, Karimnagar.
Metal Weight Calculator:
Shape:
Quantity:
Diameter:
Length:
Results
Calulated Weight: 0 Kgs / 0 Lbs