En Series Steel EN 1A

EN series steel round bar is a very popular grade of low carbon-manganese free cutting steel. EN1A is also known as 230M07. It is Available in square, round, flat or hexagon form. Equivalent to AISI 1113.


It is suitable for the manufacture of repetition turned components, such as nuts, bolts, hydraulic fittings and studs, particularly where intricate drilling and machining operations are involved.

En Series Steel EN 3A

Commonly known as “Mild Steel” in the engineering industry.It is a low to medium carbon steel.It has Very good welding properties.Can be case hardened.Low Tensile Steel (28/30 ton tensile).


Low Stress Components including low tensile shafts, bolts, nuts, bushes, spacers, flanges and light duty pulleys.Bolt Specification: 4.6 and 4.8.
Bolt Specification: 5.8 (in cold drawn condition).

En Series Steel EN2C

AISI 1018 mild/low carbon steel has excellent weldability and produces a uniform and harder case and it is considered as the best steel for carburized parts. AISI 1018 mild/low carbon steel offers a good balance of toughness, strength and ductility. Provided with higher mechanical properties, AISI 1018 hot rolled steel also includes improved machining characteristics and Brinell hardness.


Specific manufacturing controls are used for surface preparation, chemical composition, rolling and heating processes. All these processes develop a supreme quality product that are suited to fabrication processes such as welding, forging, drilling, machining, cold drawing and heat treating.

En Series Steel EN 3B

EN3B, also known as 070m20, available in rounds, flats, squares & hexagons. En3b is a mild steel suitable for welding and general machining.The term mild steel applies to all low carbon steel that does not contain any alloying elements in its makeup and has a carbon content that does not exceed 0.25%. The term “mild” is used to cover a wide range of specifications and forms for a variety of steel.Mild steel is used in mechanical engineering applications for parts that will not be subject to high stress.When in its bright cold drawn condition the steel is able to endure higher levels of stress, particularly on smaller diameters.

En Series Steel EN 6

A medium strength steel. Used to make, shafts, racks, pinions, studs, bolts, nuts, rollers, etc. Supplied as square bar, or round bar or flat.
Carbon steels have carbon as the key alloying element in their composition. They also contain up to 0.4% silicon and 1.2% manganese. In addition, the residual elements such as copper, molybdenum, aluminum, chromium and nickel are present in these steels.AISI 1035 is a water resisting carbon steel whose wear resistance and hardenability are increased by the addition of small quantity of chromium.

En Series Steel EN 8

EN8 steel also know as 080M40. Unalloyed medium carbon steel. EN8 steel is a medium strength steel, good tensile strength. Suitable for shafts, stressed pins, studs, keys etc. Available as normalized or rolled. EN8 is supplied as round drawn/turned, round hot rolled, hexagon, square, flats and plate.EN8 is usually supplied untreated but can be supplied to order in the normalized or finally heat treated (quenched and tempered to ”Q” or “R”properties for limiting ruling sections up to 63mm), which is adequate for a wide range of applications. Please refer to our selection guide for comparisons.

En Series Steel EN 8d

EN8D is a carbon steel, detailed in British Standard BS970 080A42 is a medium carbon and medium tensile steel used mainly for axles, spindles, studs, automotive and general engineering components. Suitable for heat treatment where extra strength is required.It is medium high carbon steel that can be strengthened by heat treating after forming. Machinability and weld ability are fair. Typical uses include machine, plow and carriage bolts, cylinder head studs, machine parts etc. It is also used for U bolts, concrete re-enforcing rods, forgings and non critical springs.

En Series Steel EN 8M

EN8M Products such as EN8M Flat Bar, EN8M Hex Bar and EN8M Round Bar.EN8 bright mild steel contains a lot less carbon then it use to, this mean that it is possible to weld pieces up to 18mm thick without preheating using MIG wire (SG2) or a 7018 electrode.Over 18mm would require a pre-heat of 100°C (212°F) in order to prevent cracking.Anneal afterward is recommended to prevent breaking.

En Series Steel EN 15AM

Carbon steels contain carbon as the key alloying element. They are designated by AISI four-digit numbers, and contain 0.4% of silicon and 1.2% of manganese. Molybdenum, chromium, nickel, copper, and aluminium are present in small quantities. Impurities such as sulfur and phosphorous may also be found in these steels. High machinability, used in automatic and CNC machines in mass production of components like Engine Shafts, Connecting components like Engine Shafts, Connecting rods, Spindles etc.


EN 15AM is widely used for many general engineering applications. Typical applications include shafts, studs, bolts, connecting rods, screws, rollers.

En Series Steel EN 16

EN16 also known as 605m36 comes as rolled (no heat treatment) or hardened and tempered to the ‘T’ condition. EN16T is a high tensile steel with good mechanical properties and has freedom from temper brittleness ideal for bolts, nuts, shafts and axles. Readily machinable.It is usually supplied as EN16T in accordance with BS970. It is a low alloy high tensile steel.It is supplied with a tensile range of 850 to 1000 n/mm2 depending on ruling section. EN16 has a good resistance to shock with excellent ductility. EN16 offers relief from temper brittleness. Subject to ruling section larger sizes in EN16 can be supplied in other condition such as EN16R EN16S and EN16 as rolled (un heat treated).Manganese molybdenum steel that has excellent ductility and good machinability. It has a high tensile strength as well an ability to withstand shock loading.

En Series Steel EN 9

EN 9also known as 070m55, available in diameters, flats, squares and plates with a carbon content 0.50/0.60 this is a medium carbon steel which can develop a tensile strength of 700N/mm 45tsi. In the normalized condition EN9 can be used for gears, sprockets and cams.EN9 is a medium carbon steel grade commonly supplied in the as rolled condition. It can be flame or induction hardened to produce a high surface hardness with excellent wear resistance for a carbon steel grade.

En Series Steel EN 18:

These steels are more responsive to mechanical and heat treatments than carbon steels.It is a Special structural steel.


Low end moderately stressed parts for vehicles. engines end machines where hard, wear resisting surface is needed. Hardness as surface hardened about 54HRC.

En Series Steel EN19

EN19 steel is a high quality, high tensile steel usually supplied readily machine able in ‘T’ condition, giving good ductility and shock resisting properties combined with resistance to wear.EN19T was originally introduced for the use in the machine tool and motor industries for gears, pinions, shafts, spindles and the like. Later its applications became much more extended and it is now widely used in areas such as the oil and gas industries. EN19T is suitable for applications such as gears, bolts, studs and a wide variety of applications where a good quality high tensile steel grade is suited.

En Series Steel En 24

BS970: 1955 EN24, BS970/PD970: 1970 onwards 817M40. Related European grades: 34CrNiMo6, Werkstoff No. 1.6582 US Grade: SAE (AISI) 4340. EN24 is usually supplied in the finally heat treated condition (quenched and tempered to “T” properties) up to a limiting ruling section of 250mm, which is superior to grades 605M36, 708M40 or 709M40 – see properties below. Please refer to our selection guide for comparisons.EN24 is a very popular grade of through-hardening alloy steel, which is readily machinable in the “T” condition. (Refer to our machinability guide). EN24T is most suitable for the manufacture of parts such as heavy-duty axles and shafts, gears, bolts and studs. EN24T can be further surface-hardened typically to 58-60 HRC by induction or nitride processes, producing components with enhanced wear resistance.

En Series Steel En 31

EN31 is a high carbon Alloy steel which achieves a high degree of hardness with compressive strength and abrasion resistance.

En Series Steel EN 32B

EN32 is a carbon case hardening steel. Components when carburized have a core strength range of 430-490 N/mm2 , with a hard wearing surface. It is a popular case hardening steel grade for general engineering, readily machinable and wieldable in its supply condition. EN32 is a low tensile steel suited for lightly stressed components.

En Series Steel EN 36

EN36 case hardening steel stockholders and suppliers, delivering to the whole of the South.EN36 is a 3% nickel, chromium, molybdenum grade. Carburized EN36 gives a hard case with a strong core, whilst retaining a remarkable degree of toughness.As a carburizing steel grade it is suitable for roller and ball bearings of extra light section, aero plane and motor crankshafts requiring hard surfaces for roller paths, connecting rods with case-hardened ends, as well as highly stressed gudgeon pins, gears and certain types of collets.

En Series Steel EN 36c

EN36C gives a hard case with a strong core, whilst retaining a remarkable degree of toughness.As a carburizing steel grade it is suitable for roller and ball bearings of extra light section, aero plane and motor crankshafts requiring hard surfaces for roller paths, connecting rods with case-hardened ends, as well as highly stressed gudgeon pins, gears and certain types of collets.

En Series Steel EN 41b

EN41 is a chromium-aluminum-molybdenum nit riding steel usually supplied in the hardened and tempered condition. EN41 is supplied in round bar from stock and can be cut to your requirements. EN41 ‘R’ condition has a tensile of 700-850 N/mm². EN41’S’ condition has a tensile of 775-925 N/mm². It offers high wear resistant properties together with toughness and ductility. It is defined by its suitability for nit riding from which EN41 can give a hard wear resistant case up to 68HRc, better than achievable with the similar nit riding grade EN40B

En Series Steel EN 42J

EN42J is suitable for a wide variety of spring applications including flat springs, clutches, knives, doctor blades, saw blades, agricultural tools, wood cutting saws, shims, knives, blades, shims, washers, masonry tools.

En Series Steel EN 43B

Carbon spring steel which is supplied in round bar, hexagon, flat and also as spring steel plate and sheet. Plate can be flame cut to your requirements with normalising recommended for this spring steel grade. Bar can be cut to your required lengths. Spring steel plate and sheet can be flame cut or guillotine cut to your requirements. Spring steel strip is available in coil, slit and cut to length.Spring steel, as its name suggests, is most commonly used in the manufacture of springs. When hardened and tempered (as supplied, or heat treated by the customer) it offer excellent spring characteristics.

En Series Steel EN 45

EN45 is a manganese spring steel. That is to say, it is a steel with a high carbon content, traces of manganese that effect the metal’s properties, and that it is generally used for springs (such as the suspension springs on old cars).It is suitable for oil hardening and tempering. When used in the oil hardened and tempered condition EN45 offers excellent spring characteristics. EN45 is commonly used in the automotive industries for the manufacture and repair of leaf springs.Untempered EN45 is harder than mild steel, and will not suffer as much from burs or require as much repair and therefore have a longer life.

En Series Steel EN 47

EN47 is suitable for oil hardening and tempering. When used in the oil hardened and tempered condition EN47 spring steel combines spring characteristics with good wear and abrasion resistance. When hardened EN47 offers excellent toughness and shock resistance which make it a suitable alloy spring steel for parts exposed to stress, shock and vibration.

EN47 is used widely in the motor vehicle industry and many general engineering applications. Suitable for applications that require high tensile strength and toughness. Typical applications include crankshafts, steering knuckles, gears, spindles and pumps.

En Series Steel EN 353

En 353 steel has carbon content of 0.17% and the most common form of steel as it’s provides material properties that are acceptable for many automobile applications such as heavy duty gear, shaft, pinion, cam shafts, gudgeon pins [1,8]. It is neither externally brittle nor ductile due to its lower carbon content and lower hardness. As the carbon content increases, the metal becomes harder and stronger.