SAE52100 Steel Round Bar, SAE52100 Steel Round Bar Manufacturers, SAE52100 Steel Suppliers, SAE52100 Stockist, SAE52100 Steel Dealers, SAE52100 Steel Distributors, SAE52100 Wholesalers, SAE52100 Steel Traders, SAE52100 Steel Square Distributors, SAE52100 Steel Flat Bar, SAE52100 Steel Companies Near me.
 
Grade introduction: 
SAE 52100 bearing steel is a high-quality Alloy Bearing steel, It belongs to high carbon, chromium-containing low alloy steel. SAE 52100 Oil Quenched & Tempered Hardness is 28-34 HRC. SAE 52100 steel Annealing delivery hardness less than 250HB.
SAE 52100 Alloy bearing steel properties is a chromium, manganese alloy steel specification. SAE 52100 is equivalent to DIN 100Cr6, GB GCr15 steel. Most applications can replace each other.
 
Grade application : 
SAE 52100 steel is widely used for a variety of applications in the used to the bearings in rotating machinery.
Typical applications such as valve bodies, pumps, and fittings, the high load of a wheel, bolts, double-headed bolts, gears, internal combustion engine. Electric locomotives, machine tools, tractors, steel rolling equipment, boring machine, railway vehicle, and mining machinery transmission shaft on the steel ball, roller and shaft sleeve, etc.
 
Equivalent grades : 
Country
USA
German
Japan
British
Standard
ASTM A295
DIN 17230
JIS G4805
BS 970
Grades
52100
100Cr6/1.3505
SUJ2
535A99/EN31
 
Addition to other grades
MS, EN1A, EN3B, EN8, EN8D, EN9, EN19, EN24, EN31, EN32B, EN36C, EN41B, EN43B, EN47, EN353, IS2062, 42Crmo4, OHNS, HCHCR, D2, D3, H-11, H-13, CW-1, M2, M35, M42, 2714, SKD-11, P20, P20+S, P20+Ni, SCM 420, ASTM SA-36, ASTM SA-105, SAE 1018, SAE 1020, SAE 4140, SAE 8620, 16MNCR5, 20MNCR5, C20, C35, C40, C45, C50, C60, CK45, 20C8, 40C8, 45C8, 55C8, C55MN75, S40C, S355J2G3.
 
Our Supply Range:
 
Price List:
 
People also search as:
SAE52100, SAE52100 Steel, SAE52100 Chemical composition, SAE52100 Mechanical properties, SAE52100 Equivalent Grades, SAE52100 Steel plate, SAE52100 Steel sheet, SAE52100 Manufacturers, SAE52100 Suppliers, SAE52100 Dealers, SAE52100 Stockist, SAE52100 Distributors, SAE52100 Wholesalers, SAE52100 Traders.
 
Chemical composition: 
Standard
Grade
C
Mn
P
S
Si
Ni
Cr
Cu
Mo
ASTM A295
52100
0.93-1.05
0.25-0.45
0.025
0.015
0.15-0.35
0.25
1.35-1.60
0.30
0.10
DIN 17230
100Cr6/1.3505
0.90-1.05
0.25-0.45
0.030
0.025
0.15-0.35
0.30
1.35-1.65
0.30
JIS G4805
SUJ2
0.95-1.10
0.50
0.025
0.025
0.15-0.35
1.30-1.60
BS 970
535A99/EN31
0.95-1.10
0.40-0.70
0.10-0.35
1.20-1.60
 
Mechanical properties :
Quantity
Value
Unit
Young’s modulus
200000 – 20000
MPa
Tensile strength
650 – 880
MPa
Elongation
8 – 25
%
Fatigue
275 – 275
MPa
Yield strength
350 – 350
MPa

Hardness:
Hardness, Brinell
Hardness, Knoop (converted from Rockwell C hardness)
875
875
Hardness, Rockwell C (quenched in oil from 150°C tempered)
62
62
Hardness, Rockwell C (quenched in water from 150°C tempered)
64
64
Hardness, Rockwell C (quenched in oil)
64
64
Hardness, Rockwell C (quenched in water)
66
66
Hardness, Vickers (converted from Rockwell C hardness)
848
848

 

Heat treatment properties : 
SAE 52100 alloy bearing steel is heated at 816°C followed by quenching in oil. Before performing this process, it is subjected to normalizing heat treatment at 872°C followed by slowly cooling in order to reduce the machining stress.
 
Hardening : 
SAE 52100 alloy steel is hardened by cold working, or heating and quenching. It can be carburized at 913°C (1675°F) followed by quenching. It is again heated at 788°C (1450°F) followed by quenching for the second time.
 
Tempering :
Temper to desired hardness as indicated by tempering curves after water or oil quench.
 
Physical properties : 
Properties
Metric
Imperial
Density
7.81 g/cm3
0.282 lb/in³
Melting point
1424°C
2595°F
 
Thermal properties:
Properties
Metric
Imperial
Thermal expansion co-efficient (@ 23-280°C/73.4- 36°F, annealed)
11.9 µm/m°C
6.61 µin/in°F
Thermal conductivity (typical steel)
46.6 W/mK
323 BTU in/hr.ft².°F
 
Forging properties :
AISI 52100 alloy steel is forged at 927 to 1205°C, and should not be forged below 925ºC. A post-forge equalization treatment is recommended at 745ºC for 4-6 hours followed by air cooling for SAE/AISI 52100 steel.
 
Stress relieving : 
Heat it up to 600-700℃, stay the temperature, furnace cooling. The need for the hardness of mold steel is 187-229HBS. The characters remove the work hardening and residual stress.

 

Normalizing : 
Heat it until the temperature at the range of 930-950℃, maintain the temperature, air cooling. The hardness needs to be 302-388HBS.

 

Annealing:
AISI 52100 alloy steel is annealed at 872°C (1600°F) followed by slowly cooling to reduce cold working or machining stress
 
Density :
Properties
Metric
Imperial
Density
7.81 g/cm3
0.282 lb/in³
 
Machinability : 
SAE 52100 alloy steel can be machined using conventional techniques. The machinability of this steel can be improved by performing sherardizing annealing process at 649°C (1200°F) before machining.
 
Welding:
This is a high carbon alloy typically used in bearing applications where welding is not applicable or appropriate.
 
Supply cities
Ahmedabad, Amaravathi, Ambattur, Bangalore, Belgaum, Chennai, Chittoor, Coimbatore, Dindigul, Mysore, Nellore, Hyderabad, Kochi, Mangalore, Tirupur, Tuticorin, Madurai, Andhra Pradesh, Karnataka, Puducherry, Kerala, Tamil Nadu, Telangana, Salem, Thanjavur, Trichy, Erode, Vellore, Ranipet, Sivakasi, Karur, Hosur, Nagercoil, Kanchipuram, Karaikudi, Neyveli, Cuddalore, Kumbakonam, Thiruvannamalai, Pollachi, Rajapalayam, Gudiyatham, Pudukottai, Vaniyambadi, Ambur, Nagapattinam, Trivandrum, Vijayawada, Guntur, Thirupathi, Nazarathpet, Kakinada, Kurnool, Kadapa, Nizamabad, Mahabubnagar, Karimnagar.

Metal Weight Calculator:
Shape:
Quantity:
Diameter:
Length:
Results
Calulated Weight: 0 Kgs / 0 Lbs